+1 (971) 293-4200 — 24/7 Emergency Plumbing Portland
+1 (971) 293-4200 Portland, OR 97214 24/7 Dispatch

Garbage Disposal

How to Reset a Garbage Disposal (and What to Do If It Won’t Reset)

To reset a garbage disposal, turn it off, find the red button on the underside of the unit and press it in firmly. If it stays dead, the button pops back out or it hums without spinning, the cause is a jam or a failing motor, not a missing reset.

+1 (971) 293-4200 Call Now — We Answer 24/7
Plain-language guideWritten quotesPortland, OR

Reset It in Four Steps

A tripped overload protector is the most common reason a disposal goes dead.

Switch it off first

Turn the disposal off at the wall or air switch. Never put a hand inside it, even when it is off.

Find the red button

Look under the sink at the bottom of the unit, facing the floor, for a small red button.

Press and wait

Press the button firmly. If it will not stay in, wait about ten minutes and try again.

Know when to stop

Repeated tripping, a burning smell or a leak means the unit needs a plumber, not another reset.

Quick answer: switch the disposal off, find the red button on the bottom of the unit, press it firmly until it stays in, then switch the disposal on with cold water running. If the button will not stay in, wait ten minutes and try again.

Where the reset button is

On most disposals the reset is a small red button on the bottom of the unit, facing the floor, under the sink. InSinkErator calls it the overload protector. Shine a flashlight at the underside and look for a red, square button. Some models, mainly older ones and some other brands, may not have one, so check the label or manual for your model.

How to reset it, step by step

  • Step 1: Switch the disposal off at the wall switch or air switch.
  • Step 2: Look under the sink at the bottom of the unit and find the red button.
  • Step 3: Check whether it has tripped. On InSinkErator units a tripped button sits about a quarter inch lower than normal.
  • Step 4: Press the red button firmly until it clicks and stays in.
  • Step 5: If it will not stay in, wait ten minutes so the motor can cool, then press it again.
  • Step 6: Switch the disposal on and run cold water. If it runs normally, you are done.

Some newer InSinkErator EZ Connect models have no button. Their overload switch is automatic: turn the unit off, let it cool for up to 20 minutes (and unplug it first if it uses a push-button air switch), then turn it back on.

Why it tripped in the first place

The reset button is a safety cut-off. It trips when the motor works too hard or overheats. The usual causes are:

  • A jam: a bone, fruit pit, utensil or hard food wedged against the blades.
  • Too much at once: a big load of fibrous or starchy food run without enough water.
  • A worn-out motor: common once the unit is past about 10 years old.
  • An electrical fault at the outlet, switch or wiring.

Pressing reset does not clear a jam. If the disposal hums but does not spin, see why a garbage disposal hums but will not turn, or switch it off, unplug it, and free the blades from the underside with the wrench your manual specifies.

When resetting stops working

Call a plumber if any of these happen:

  • The button trips again within minutes, or you have reset it several times this month.
  • The button will not stay in after the ten-minute wait.
  • You smell burning or see smoke. Switch off the breaker and do not use the unit.
  • Water leaks from the bottom or from the reset button area.
  • The disposal is more than about 10 years old and keeps failing.

Premier Portland Plumbers diagnoses and replaces garbage disposals around the clock. See our emergency garbage disposal repair page, or call +1 (971) 293-4200. A licensed plumber will tell you whether it is a reset, a repair or a replacement before any work starts. If the sink itself is clogged, see garbage disposal vs. sink clog.

Common Questions

What Portland homeowners ask about this topic.

A jam, an overload or a failing motor. If it trips again right after a reset, stop and have it inspected.
No. Many have a red button on the underside, but some models have none or use an automatic overload switch. Check your manual.
Pressing it a few times to clear one overload is normal. Repeated tripping means the cause has not been fixed.
The blades are jammed. Switch it off, unplug it, free the blades from the underside as your manual describes, then press reset.
Switch the disposal off first. If you are unsure about electrical safety, switch the breaker off.

Related Reading

Garbage Disposal vs. Sink ClogWhy Your Kitchen Drain Keeps CloggingHow Long Garbage Disposals Last

Our Services

Garbage Disposal RepairDrain CleaningEmergency Drain Cleaning

Garbage Disposal Not Working in Portland?

Call with the symptoms and the age of the unit to discuss a repair or replacement and a written quote.

+1 (971) 293-4200 Call for Immediate Dispatch
Call Now — 24/7 Dispatch